Porta-fusível de bateria GFEVH | 30A–800A, 12V–500V CC
Porta-fusível de circuito único GFEVH para baterias: 30A–800A, 12V–500V CC, capacidade de interrupção de 2 kA, baquelite preta UL94 V-0, resistência de contato <5mΩ. Para carros e embarcações.
Solicite um orçamento
GFEVH Single-Circuit Battery Fuse Holder — 30A to 800A, 12V–500V DC
Built for automotive and marine battery protection fuses. Black Bakelite UL94 V-0 base, 2 kA breaking capacity, contact resistance below 5 mΩ.
12V–500V DC
2 kA Breaking
Black Bakelite V-0
<5 mΩ Contact R.
Because starter and house batteries feed high instantaneous currents, cars and ships need a dedicated battery fuse holder. In particular, the GFEVH covers 30A to 800A at 12V–500V DC. Moreover, its black Bakelite base meets UL94 V-0. As a result, it protects main battery feeds against short circuits.
Visão geral do produto (para referência rápida)
- Model: GFEVH single-circuit battery fuse holder.
- Ratings: 12V–500V DC; 30A–800A.
- Breaking capacity: 2 kA.
- Base: black Bakelite, UL94 V-0; hardware per GB/T 20878-2007.
- Electrical: withstand 1500VAC; contact resistance <5mΩ; insulation >100MΩ.
- Use: car and ship battery protection fuse circuits.
Especificações
| Modelo do produto | GFEVH single-circuit battery fuse holder |
|---|---|
| Tensão nominal | 12V – 500V DC |
| Corrente nominal | 30A – 800A |
| Capacidade de ruptura | 2 kA |
| Base | Black Bakelite, UL94 V-0 |
| Fixadores | Per GB/T 20878-2007 |
| Withstand voltage | 1500 VAC |
| Contact resistance | < 5 mΩ |
| Insulation resistance | > 100 MΩ |
| Aplicativo | Car and ship battery protection fuses |
Principais características
- Wide current span: 30A up to 800A for single battery circuits.
- 12V–500V DC range: covers cars, marine and higher-voltage battery systems.
- 2 kA breaking: clears typical battery short-circuit faults.
- UL94 V-0 Bakelite base: flame-retardant and mechanically rigid.
- Low contact resistance: <5mΩ keeps heating low under load.
Why it protects car and marine batteries
Because battery cables run straight from the terminal to the load, a short circuit can dump very high current in milliseconds. Consequently, installers choose a dedicated battery fuse holder rather than an ordinary terminal block. For example, an 800A link protects a heavy inverter-to-battery cable in a yacht. However, you must never size the fuse above the cable’s ampacity. In addition, the <5mΩ contact resistance limits I²R heating.
How to install
First, mount the holder close to the battery positive terminal. Next, connect the battery lead and the load lead to the studs. Then insert the correct battery protection fuse. Finally, torque the fasteners to the recommended value and snap on the cover. If you need a specific stud size, simply specify at order time.
Mechanical Dimensions (mm, per factory drawing)
| Dimensão | Valor (mm) | Notas |
|---|---|---|
| Comprimento total | 61.9 | End-to-end |
| Total height | 46.4 | From base to top of stud |
| Stud height above base | 21.7 | Upper step height |
| Base step height | 10.6 | Lower step |
| Mounting offset | 15.3 / 4.2 | Hole positions per drawing |
| Stud hole | Ø10 | Cross-section stud |
Dimensions per manufacturer drawing; verify against latest datasheet before production.
Aplicações
- Automotive main battery and alternator feed protection
- Marine / boat house battery and starter battery circuits
- RV and off-grid vehicle DC distribution
- High-current DC auxiliary systems up to 500V DC
- Battery-to-inverter and battery-to-charger protection
